Rc Hobby Items In Pakistan, Faisalabad (2026)

Photos from Rc Hobby Items In Pakistan's post

16/03/2016

HobbyKing KK2.1HC Multi-Rotor Hard Case Flight Control Board With Remote Programmer stock available

The next evolution of the rotor revolution is here!! The KK2.1HC (Hard Case) is packing new found power with updated sensors, memory, header pins, hard case and remote programmer.
The KK2.1HC is the next big evolution of the first generation KK flight control boards. The KK2.1HC was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The remote LCD screen and built in software makes installing and setup easier than ever. The screen and programing buttons have been relocated to a remote plug-in programmer and a hard case installed, this makes the KK extremely durable. The plug in programmer uses the exact same format as the onboard version and can be plugged in at anytime for a quick value change. This new design allows the KK to be installed in frames where access to the onboard buttons and screen was an issue, you can even leave the cable plugged into the KK side and run it out for access to the programmer. The Hard case still retains the standardized 45mm mounting holes and has the buzzer is now internally mounted. Mounting locations and damage to the LCD screen is a thing of the past.
A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system, making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1HC is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The KK2.1HC added polarity protection to the voltage sense header and on-board buzzer. The voltage sense line has been updated for better accuracy. The Hard case is clearly labeled, making installation and connections a snap.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1HC was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
Specs:
Size: 55mm x 55mm x 19mm
Weight: 32g
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.6:
Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Singlecopter 2M 2S
Singlecopter 1M 4S

(Custom Mix via the "Mixer Editor" option)
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
* Note: The programmer does NOT need to remain plugged in for the KK to operate, Simply plug in, program, unplug then fly
** Note: It is all ways recommended to update to the latest software version as part of your initial setup.(This is different than v1. 6 for KK2.0)
*** Note: The KK2.1HC uses the same firmware as the KK2.1~2.1.5

16/03/2016

CopterControl from the OpenPilot project introduces a new generation of multi-purpose aircraft stabilization platforms. The CC3D boards is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software.
The CC3D is an update to the original Copter Control board, now using the powerful single chip IMU. The board shares a lot with the Revolution platform, including the powerful OpenPilot architecture and the cross-platform Ground Control Station (GCS). The CopterControl platform has been designed from the ground up to perform a host of functions from auto-level, multi-copter, Fixed wing UAV’s and even Flybarless Helicopter support. The new included Flexiport provides either I2C connectivity or a second serial port.
OpenPilot has made their flight controller as easy and trouble-free as possible. The Open Pilot project, whilst still young, it's trying to make Open Source much more user friendly. You won’t need to buy add-on boards or extra chip programmers. Don’t be fooled by the price. CopterControl provides comparable functionality to other high-end autopilots at a small fraction of the cost. Commercial projects will charge what they can get away with, regardless of quality or features. The non-profit OpenPilot project is different. Consider getting involved and helping the progress.
The HobbyKing CC3D board is fully authorized by OpenPilot and built with quality import parts, (unlike the cheap copy boards that can suffer from voltage fluctuations). A portion of the sales of each unit is donated back to the OpenPilot project.
Features:
• MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters
• Flybarless Helicopter controller with auto-level
• Fixed Wing UAV controller
• Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM
• 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer
• Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
• Software support for Windows, Mac and Linux
• Direct high speed USB support with no drivers required, a truly plug and play device.
• Spektrum satellite receiver support
• Futaba S-BUS hardware support and PPM
• Innovative Flexi-port technology for superior port flexibility
• 4Mbits on-board EEPROM for configuration storage

Specs:
Size: 36x36mm
Weight: 5.7g
Mounting: M3 holes @ 30.5mm square
Included:
CC3D Flight controller Rev C with V4 bootloader pre installed
Full cable set to match the onboard ports
OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it! www.Openpilot.org

For price inbox a msg

16/03/2016

Openpilot Mini CC3D Flight Control Board in stock

This is the new Mini CC3D flight controller. It is about half the size of the regular CC3D but has the same functionality. The Mini CC3D board is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software.
Using the powerful STM32 32-bit micro-controller gives you crisp handling characteristics when flying your flying tricopter, quad, hex, octocopter, and even fixed wing planes. The tiny size allows you to fit this on even the smallest frames.
Don’t be fooled by the size. Mini CC3D provides comparable functionality to other high-end flight controllers at a small fraction of the cost.
Features:
• About half the size of the regular OpenPilot CC3D, but with the same functionality.
• The CC3D provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes.
• Powerful STM32 32-bit micro-controller running at 90MIPs with 128KB Flash and 20KB RAM.
• 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
• 4 layer PCB for superior electrical noise reduction and flight performance.
• Software support for Windows, Mac and Linux.
• Direct high speed USB support with no drivers required.
• Spektrum satellite receiver support.
• Futaba S-BUS hardware support.
• Innovative Flexi-port technology for superior port flexibility.
• 4Mbits on-board EEPROM for configuration storage.
• This OpenPilot Mini CC3D board comes in a high quality, protective case.
• Horizontal pin
Specs:
Size: 28x21x9mm
Weight: 4g

Inbox for price