Salient Ocean Adventures

  • Home
  • Salient Ocean Adventures
Directions Website

Salient Ocean Adventures Welcome to the Salient Racing Team page.
We are an amateur racing team Join us on this adventure!

We are an amateur racing team and will share our story while preparing for the Vic-Maui 2018 Race.

Awesome day on the water. A nice escape after what must be one of the more crazy weeks the world has seen in recent year...
16/03/2020

Awesome day on the water. A nice escape after what must be one of the more crazy weeks the world has seen in recent years.
Steady 15-20 kts from the north west, clear sky, not a cloud to be seen.
Champagne sailing pure!

Maiden is the story of the first ever all-female crew to enter the 1989 Whitbread Round the World Sailing Race. Maiden i...
07/02/2020

Maiden is the story of the first ever all-female crew to enter the 1989 Whitbread Round the World Sailing Race. Maiden is named best documentary 2019 by the National Board of Review.

Theresa Riedl, of Vancouver will join us after the screening to share her stories of crewing on the Maiden from Hawaii to Vancouver- Summer 2019.

Maiden Documentary Screening and Q&A by Room to Read – Vancouver Chapter - Wednesday, March 4, 2020 06:00 PM at Community Centre – Olympic Village, Multipurpose Room 4 in . Buy tickets and find information on Universe.

06/02/2020

With over 125 combined presentations, Boating experts from around the world educate, inspire and entertain at the Vancouver Boat Show, sharing their experience and expertise on everything from boating basics to spellbinding boating adventures.

One project was planned - one not so much (See first two pictures).Over the past 18 months we had an oil leak on the eng...
31/12/2019

One project was planned - one not so much (See first two pictures).

Over the past 18 months we had an oil leak on the engine that got bigger and bigger. Not dramatic, but enough to make a mess. These things do not fix themselves and I have seen what happens when those issues do not get addressed.

Talking to Brad & Adam at First Yachts and Doug who helps me with boat maintenance the consensus was that the rear seal on the engine likely leaks. It also appears that the oil drain plug leaks. The oil pan shows some corrosion which might become an issue as well.

It was also time to get the exhaust riser inspected & likely replaced. The radiator needed to be inspected & pressure tested too.

With all this work to be done and on the advice of FYS I decided to take the engine off the boat and do a proper overhaul with the engine in the shop. Technically, it is possible to get at the rear seal without pulling the engine, but having to do all this work I thought it is time to replace the boot on the saildrive and look for any other issues the engine might have.

Getting the engine ready for removal was straightforward and took just over half a day of work. Prepping for the lift, hauling the boat and pulling the engine took the better part of a day including a lot of waiting.

Then stuff started to get interesting. The first surprise was some corrosion around the air intakes. We decided to remove the air intake manifold as well as the exhaust manifold as there was a lot of corrosion that I never saw with the engine in place (see picture 4, exhaust manifold). It was clear something was leaking at some point. We will find out later what.

To get to the rear seal, we had to remove the bellhousing, then the damper plate and finally the flywheel. See the next picture showing the fly wheel & damper plate still in place. And there was the second surprise: The engine has been partially under water twice: You can see the two "tide lines". Luckily, the water did not reach the starter motor and damage was only 'cosmetic'.

Next: Remove the damper plate. Apparently the rubber disintegrates typically between 3000 & 4000 hours. Salient's engine clocks at 2,500 hours so I was curious what we would find. The next two pictures show the damper plate, and oh boy is it ever shot. This would have not lasted another 500 hours and we would have had a serious problem, likely at the most inconvenient time. Replacement cost: $1,200.

In the next picture you can see the rear seal. That was at the heart of why we are doing this operation. The seal is indeed damaged, explaining the oil leak.

On to the next surprise: While I expected the exhaust riser would have to be cleaned and possibly replaced (it's coming up to 5 years of service), we noticed the water ni**le is "cut off". This is not damage that happened during operation, but is a casting deficiency. Talking to a marine mechanic looking at the engine today, he said this is likely the source of the corrosion I mentioned above.

For now we have disassembled most of what we have to and we are mainly through the cleaning of all the parts. The radiator and manifold are off to the radiator shop for cleaning & pressure testing. All the other corroded parts are mostly cleaned up and will get painted too. More on that in a later post.

Practical tips:
Your best friends:
A sharpie pen, masking tape, ziplock bags & your phone.

1) Take lots of pictures as you take systems apart.

2) Label everything you disconnect. Then take pictures. Labels will disappear.

3) Put every fitting, fastener, nut you take off and put it in a ziplock bag and label the bag. Have a bag for each system and subsystem. This is not the time to "save on plastic".

4) Removing gaskets will be the most time consuming task: A couple of scrapers / wedges made of G10, medium and fine emery cloth plus lot's of elbow grease & even more patience will do the trick.

5) Talk to your mechanic as you go along & have him look over the project. A professional will be able to point out potential issues you might have overlooked or items that come up for replacement after a certain amount of hours. Think of lift pump, circulation pump, glow plugs, raw water pump re-build to name a few items.

6) Have a coach. I am lucky to have Adam & Doug along side ready with advice & tips as I am stumbling through this project. WIthout them I would have not dared to embark on this mission.

7) Parts: Parts4Engines in the UK sell many of the parts for half the price they are in Canada. These are original Perkins Parts. Volvo does not build marine engines, these are Perkins Engines (BTW: They do also have Yanmar parts).

There is a great site in Europe that shows "exploded diagrams" of each system: https://www.volvopentashop.com/
Sadly, they do not sell parts to Canada or the US nor can one download those diagrams. A great resource nevertheless. My mechanic uses the same website I found out today :)

More to come as I keep going and start to put things back together.

In parallel we also remove the sail drive and deal with the "unplanned project" in the 2nd pictures. More on those in the new year.

Comments, thoughts & suggestions are most welcome!

, , ,

Salient was on the hard for almost two weeks and much work has been done.Some minor damage repair on the keel from a log...
20/10/2019

Salient was on the hard for almost two weeks and much work has been done.

Some minor damage repair on the keel from a log strike needed attention. Many thanks to Rod of FYS who gave me a tutorial on how to grind out the affected area to bare lead and build it back up again with different types of epoxy and bottom paint. A long process involving seven layers of protection. All very interesting.

While the boat was out of the water we removed the rudder & checked the bearings. Recent issues on other boats with the same Jeffa bearings lead to some concern: The aluminum outer race can corrode, squeezing the bearing to the point where steering becomes hard or the rudder seizes completely. I watched others banging out the rudder with a sledge hammer.

An inspection on Salient’s bearing showed the inside of the aluminum race clean as a whistle. However, at the bottom there was a small area where Sikaflex caulking was not cleaned up resulted in crevice corrosion. Cleaned it up, coated it with epoxy and painted with Trilux bottom paint. Best to spot these things early before they become an issue.

While at it, we removed the quadrant which looked ok. However, a thorough inspection was difficult as there was some corrosion & the coating started to come off. We had it sandblasted to properly inspected it. The quadrant now looks like new.

The last item on the “steering system" list included the emergency tiller. Years of being stowed in the locker showed badly. We had it sandblasted and coated it with anti-corrosion paint (Kryptonite). While at it, we also had a couple gussets welded to the handle bar. I was told by a serious sailor that this might be a weak spot if we were actually to use the emergency tiller for any length of time in open ocean conditions.

Some might think this is excessive, but the steering system is such an important system on a boat that it deserves the utmost attention.

Another annual ritual on Salient is to check the torque on the keel bolts.
All checked out as well.

Last but not least Salient got a good polishing & waxing. I much enjoy the early Saturday fall mornings in the yard, listing to my favorite tunes and getting Salient’s topside to a shiny “looks like new”.

I was lucky to have great advice & help from First Yachts doing all this work. This made it both enjoyable and resulted in a good effort to improve the boat or at least maintain it in good shape for serious sailing :)

TLC round two: Cut-polishing done. Shiny topsides 🙂Waxing next!Ah...and some good news on the technical front: No water ...
30/09/2019

TLC round two:
Cut-polishing done. Shiny topsides 🙂
Waxing next!

Ah...and some good news on the technical front: No water in the gear oil. Replacing the prop shaft seals did the trick 🙂

Some TLC on a sunny weekend!
29/09/2019

Some TLC on a sunny weekend!

Over the past weeks Salient had some more maintenance done. When one of the instructors reported the speed no longer rea...
20/09/2019

Over the past weeks Salient had some more maintenance done. When one of the instructors reported the speed no longer reads, even after checking the paddle wheel I was a bit worried that we might have a bigger problem. Turns out that the marine life grows at an astonishing rate in the warm summer months. What you can see in the pictures developed in a matter of days. Cleaned it all up and the 'speedo" works like advertised again.

The solenoid on the propane tank was pretty rusty and we changed it before it decided to quite. While doing that I had a closer look at the propane hose and noted in horror that it showed some serious cracks. Replaced it immediately. I should have seen this before it developed that badly, but overlooked it. A good reminder to all boaters to carefully check their propane system.

Here is a minor nuisance problem: The end caps on the OceanAir blinds seem to go missing - especially after rougher ocean crossings. The only place I found that sells those is in the UK and they charge over 14 GBP plus shipping - for the pair!! If anyone has a better source, please let me know! Thank you in advance.

On to an issue that stinks: Found this product "Shock Treat"- it will clear out the sludge in your holding tank and get rid of the odor. Works fantastic and I highly recommend this treatment for your holding tank. Plus it is environmentally friendly! Your crew will be grateful.
Salient's holding tank is "in the green" after this treatment :)

Finally, a bit of a rant: Each time I see someone "ratcheting" a winch I cringe. Are people just lazy to do a full turn or they simply do not understand how a winch works? On Salient all winches are two speeds. If it gets hard to turn one way, turn it the other way. Shifting gears, just like on a bike :). The other day a skipper on Salient reported one of the winches does not work properly. I took it apart and found a broken pawl (see pic). "Ratchig" instead of properly using winch will result in this sort of damage much quicker.

That's it for todays maintenance update - more to come and hopefully some sailing news before too long.

Toe rail part two - Learnt a lot when installing the new composite toe rails supplied by Beneteau: 1. The fasteners need...
14/09/2019

Toe rail part two - Learnt a lot when installing the new composite toe rails supplied by Beneteau:
1. The fasteners need very little torque.
2. Do not do this on a sunny, hot day. The material gets very soft and behaves like spaghetti.

This resulted in some sagging of the material between fasteners and low spots where the fasteners were.

Nothing I could do about the sagging. Once the toe rail is bedded with Sikaflex 291 it wont move. The low spots I managed to grind out using an electrical plan & longboard. The electric plan works fantastic. Don't worry if the material looks like 'plastic' once you planned it. Sanding it will make it look like wood again.

Tip 1: I don't recommend an electric sander. The material can get too hot and might melt.
Tip 2: Use Sikaflex long opening time (291LOT)
Tip 3: Clamp toe rail against stanchions
Tip 3: Put a fastener within 2" of the end of the toe rail

I am happy with the results and when I do the forward toe rails it will be perfect and hopefully without needing to plane & sand :)

If you ever want to install new toe rails - give me a call. Happy to let you know all the tricks.

Here is a lighter post for a rainy Friday. Any guess what this is (fist pic) and how it came about? Let your fantasy fre...
13/09/2019

Here is a lighter post for a rainy Friday. Any guess what this is (fist pic) and how it came about? Let your fantasy free reign and share your thoughts!

Hint - it was part of the operation "change rode."

And on a more serious note: While you are at it - when is the last time you serviced your windlass?

I do admit I was way behind on that one, but it is finally done. Not a big job if done periodically, but I could for the life of me not get the wheel off - it was so stuck. Thank you Adam at FYS for lending me a strong hand.

Address


Alerts

Be the first to know and let us send you an email when Salient Ocean Adventures posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

  • Want your business to be the top-listed gym/sports facility?

Share